Click To Call(656) 269-5576Click To Get A Free Estimate
Warm red brick paver walkway curving past a flower bed at a FishHawk home

Keep the warm look of brick and slow the fade

Brick Paver Sealing in FishHawk, FL

Free estimates for brick pavers in FishHawk, with a reply inside 1 business day: call (656) 269-5576.

  • Brings out deeper paver color
  • Fresh joint sand helps lock pavers in place
  • Gives weeds less room to grow
  • Makes the surface easier to keep clean
  • Free estimate, no obligation

Request a Free Estimate

Free, no obligation.

Step 1 of 2

Where are your pavers?

Please choose one.

Free EstimateNo obligation
Fast ReplyWithin 1 business day, usually much sooner
Typical Local Price$1.75 to $3.00 a sq ft to clean, sand and seal
Call Now(656) 269-5576

Who can seal brick pavers in FishHawk, and how soon is the reply?

A local contractor can seal brick pavers for FishHawk homes, and a reply comes inside 1 business day, usually much sooner. The visit and the written price are free, with no obligation. To get started, call (656) 269-5576.

Brick takes a different touch than other pavers. It soaks up more water, and the wrong finish can leave it blotchy. A careful wash, fresh sand and the right coat keep the warm color without a plastic shine, and they slow the fade that full Florida sun brings to older walks, steps and entries. If the numbers are the next thing you want, ask for a free estimate.

Call (656) 269-5576

How is sealing brick different from sealing concrete pavers?

Brick is thirstier. Unilock says brick pavers are more absorbent than concrete and usually call for a matte or low gloss sealer. A paver sealer guide describes clay as porous and recommends a penetrating, siloxane sealer that protects without changing the color. To ask which kind your pavers are, call (656) 269-5576.

Why is a glossy coat the risk on brick?

Gloss is the risk. The same guide says shiny sealers dry blotchy on clay. Concrete pavers handle a deeper wet look better. If you cannot tell which you have, a contractor can usually say after a look and a small test, so ask for a free estimate.

Hand-held scrub brush working across red brick pavers with moss in the joints

Should the finish on brick be matte, low gloss or wet look?

Matte or low gloss is the safe choice for brick, according to Unilock, and the guide for clay says to avoid wet look and gloss. Matte also keeps better grip, since Unilock says high gloss can be slippery when wet. Wet look is more of a concrete paver choice. To see samples, ask for a free estimate.

Does a natural finish help with the HOA?

A paver company serving FishHawk says color-enhancing and wet look finishes are more likely to need HOA approval, so a natural finish on brick also tends to be the easier request. Questions about what your association allows go to the association. For finish ideas, call (656) 269-5576.

How it works

What does the brick paver sealing process look like?

The brick paver sealing process runs in a set order, and drying time matters more on brick than on other pavers. To get on the schedule, call (656) 269-5576.

1. Check and test

The contractor looks for loose bricks, old sealer and stains, then tries a product on a hidden corner.

2. Strip if needed

Old sealer that peels or clouds is removed first, as Premier Coatings describes for brick in Florida.

3. Wash

A low pressure wash lifts dirt, moss and growth. Unilock warns against a wire brush.

4. Dry

A paver sealer guide says to let brick dry one to two days after the wash. Unilock says shade takes longer.

5. Sand and seal

Joints are filled, and sealer goes on the bricks and the joints together, per the clay sealing guide.

Why choose us

Why do brick pavers show white spots after a rain?

Salts move through the brick and are left on the surface as the water dries. That white deposit is called efflorescence. A paver sealer guide says sealer will not stop it, and Unilock says it should be gone before any coat goes on, usually in 2 to 3 months but sometimes up to a year. A paver company serving FishHawk adds that sealing over it traps a cloudy look. To ask what you have, call (656) 269-5576.

New installs have a waiting period for this reason, and many installers wait 60 to 90 days before sealing. If your bricks are newer, give the installation date when you ask for a free estimate.

Why choose us

Why is sealing old brick in FishHawk a stripping job so often?

Failed sealer on brick leaves a blotchy surface. Premier Coatings shows a Florida brick job where the old coat was never stripped and the finish came out uneven. It also lists milky residue, faded color and washed out sand as signs of failed work. A fresh coat does not fix those. To have an old coat looked at, ask for a free estimate.

The first houses in FishHawk Trails and FishHawk Ranch date to the 1990s, so some brick surfaces have seen more than one coat. If you know the date or product of the last one, say so. For other questions, call (656) 269-5576.

Contractor rinsing a red brick patio edge with a wand while joint sand is swept to one side
Pricing

How much does brick paver sealing cost in FishHawk?

No page prices brick on its own, so the table starts from the $1.75 to $3.00 per square foot a paver company serving FishHawk lists for cleaning, sand and sealing. Sealer alone for one coat, using Unilock's gallon price and coverage, is a small slice of the job. Brick can need stripping or a slower dry time, which moves the price. For a number on yours, ask for a free estimate.

Paved areaExampleSealer alone, one coatClean, sand and seal
250 sq ftBrick walkway and entry$132 to $470$438 to $750
500 sq ftBrick patio$265 to $940$875 to $1,500
900 sq ftBrick driveway or large lanai$477 to $1,692$1,575 to $2,700

Sealer alone is about $0.53 to $1.88 per square foot from Unilock's 80 to 150 square feet a gallon and $80 to $150 a gallon. The full job uses the $1.75 to $3.00 range. Stripping old sealer and repairs are usually extra.

Get a Free Estimate

How often do brick pavers in FishHawk need a new coat?

Brick coats usually run two to five years between visits, with bright sun at the front door wearing them down sooner. A paver company serving FishHawk gives that range and says traffic and sprinkler overspray shorten it. Premier Coatings says 2 to 3 years on Florida surfaces and Unilock says 3 to 5. Faded color, milky film and washed out sand are the signs to watch. To have your bricks checked, call (656) 269-5576.

Can the sprinklers be left running near sealed brick?

Not during the cure. Unilock says water on a fresh coat can leave white marks, so the sprinklers stay off while it dries for about 24 hours and cures for up to 48 hours of dry weather. After that, spray that hits the brick can leave rust, and a Florida pressure cleaning company says iron in well water is a common cause. To tell the contractor about your heads, ask for a free estimate.

Questions

What do owners ask before sealing brick?

Should I seal my brick pavers?

Usually, when they have faded, hold green growth or let joint sand wash out. Unilock says brick pavers are more absorbent than concrete, so a sealer has more to protect, and it points to matte or low gloss for them.

Should pavers be sealed in Florida?

Most sources say yes once color fades or joints empty. Sun, summer rain and sprinkler spray work on pavers all year. A paver company serving FishHawk gives 2 to 5 years between coats, and the choice of finish matters more on brick.

Can I pressure wash brick pavers?

With care. A fan nozzle held at an angle keeps pressure low, and Unilock warns that too much can blow sand from the joints. Softer brick can mark under a washer, so a contractor tests a corner first.

Do I need to clean my pavers before sealing them?

Yes. Sealer locks in whatever is on the surface, Premier Coatings says, and Unilock adds that it can make leftover stains stand out. A clean, dry surface is the starting point.

How often should I seal pavers in Florida?

Two to five years is the range from a paver company serving FishHawk. A Florida sealing company says 2 to 3 and Unilock says 3 to 5. Look for water soaking in rather than beading.

How much does it cost to have your pavers sealed?

A paver company serving FishHawk lists about $1.75 to $3.00 or more per square foot for cleaning, sand and sealing. No page read prices brick on its own, so ask for a written number after the contractor sees the surface.

Why did my brick pavers get white spots?

White haze is usually efflorescence, a salt that rises to the surface. A paver sealer guide says sealer will not stop it. Unilock says to wait until it fades, which usually takes 2 to 3 months and sometimes up to a year.

Will sealer change the color of clay brick pavers?

A penetrating sealer is meant to keep the color. Clay brick is porous, a paver sealer guide says, and gloss or wet look products can dry blotchy on it. Ask for a test patch.

Photos

What do sealed brick pavers look like in FishHawk?

Freshly sealed paver driveway on a brick surface in FishHawk
Sealed paver pool deck on a brick surface in FishHawk
Sealed paver patio behind the home on a brick surface in FishHawk
Sealed paver walkway to a front door on a brick surface in FishHawk
Close view of freshly sealed pavers on a brick surface in FishHawk
Paver area with one cleaned half beside a dirty half on a brick surface in FishHawk
Contractor cleaning pavers on a brick surface in FishHawk
Contractor sealing or sanding pavers on a brick surface in FishHawk

Ready to protect the brick?

Send the form or call, and a free brick sealing estimate returns inside 1 business day, usually much sooner.

Call (656) 269-5576

Free, no obligation